cover photo

BLOG · 16/10/2026

EV-RE Level 1 Report Part 2

EV-RE Level 1 Report Part 2
This Article is yet to be approved by a Coordinator.

Task 9: Blink LED WITH STM32 (Embedded)

Objectives: Blink an LED using STM32

Softwares used: STM32CubeIDE, STM32CubeMX, STM32CubeProgrammer

Outcomes and Learnings: STM32 is a family of 32-bit microcontrollers based on the ARM Cortex-M processor core, designed and manufactured by STMicroelectronics. They function as tiny computers on a single chip, combining a central processing unit (CPU), Flash memory, SRAM, and input/output peripherals. They are widely used in consumer electronics, robotics, industrial automation, and internet-of-things (IoT) devices. I was exposed to the environment of STM32 and I got to know some beginner level stuff like the different types of STM32 boards, all the softwares required to run the STM32 and also I blinked the inbuilt LED present in the STM32.

Task 10: Auto Night Lamp Using LED for Electric Vehicles (Embedded)

Objectives: Design a light-sensitive LED circuit using an LDR and a BJT transistor. The LED turns on when light levels drop, simulating an automatic headlamp system for EVs. Test using a mobile flashlight for light detection.

Outcomes and Learnings: This task was a demonstration of how the lamps turn on themselves during night time for vehicles. In this task we use an LDR to measure the light source and when the light source is very less and darkness is present around the LDR, it sends a signal to the Transistor which turns on the LED automatically. The circuit diagram is as follows img And here is my task img2

Task 11: Buck Converter on LTspice (Power Electronics)

Objectives: Design and simulate a DC-DC buck converter in LTspice. Observe input and output voltages, inductor current waveform, and switching frequency. Understand step-down conversion and efficiency aspects.

Software used: LTspice

Outcomes and Learnings: Buck converter or DC Step Down Chopper is a type of power circuit which steps down a high input voltage to a lower output voltage while keeping high power efficiency. A buck converter involves a switch (MOSFET/IGBT), an inductor and a capacitor. The value of the inductor and capacitor determines the magnitude of output voltage. I simulated the Buck converter in LTspice and made my observation on the waveforms of Input and output voltage, the pulse voltage and current through the Inductor. Here is my simulation img This image shows my simulation along with the waveforms of imput voltage at 12V which is a green line and the output voltage which is around 5V shown as red line. img2 In this image, we can see the waveforms of pulses in red colour and the inductor current in green.

Task 12: Wireless Charger Simulation on Tinkercad (Power Electronics)

Objectives: Simulate inductive power transfer between a transmitter and receiver coil on Tinkercad using basic circuit blocks. Demonstrates wireless charging principles through virtual components and LED indication.

Software used: Tinkercad

Outcomes and Learnings: This task requires us to show the inductive power transfer between two coils in TinkerCAD. Since TinkerCAD cannot simulate the inductive effect between two coils it is not possible to show the flow of power. image

Task 13: Utilizing Transistors as Switches and Voltage Regulators (Power Electronics)

Objectives: Understand how transistors can be used as digital switches and basic voltage regulators. Begin by using an Arduino to send a digital signal to the base of a transistor to control an LED (ON/OFF). Then, explore how a transistor introduces voltage drop by simulating a circuit in Tinkercad — Observe how voltage reduces across the LED after adding a transistor.

Softwares used: Tinkercad and Arduino IDE

Outcomes and Learnings: Transistors can be operated in 3 different regions namely Active region, Saturation region and Cut-off region. In active region, it acts as an amplifier which amplifies the input signals whereas in Saturation and Cut-off regions it acts as a switch. Saturation Region: Sufficient base current is supplied to drive both junctions into forward bias. The transistor acts as a closed switch, allowing maximum load current to flow. Cut-off Region: The Base-Emitter junction is reverse-biased or unbiased. The transistor acts as an open switch, blocking current flow through the LED. image

Transistor as Voltage Regulator: A transistor can also act as a voltage regulator by functioning as a variable resistor in series with the load, using a stable reference voltage (usually from a Zener diode) at its base to absorb input voltage changes and keep the output voltage steady.

Here is the simulation of given task in Tinkercad

In the above video we can observe that when the transistor is turned on (when LED glows), the voltage across collector and emitter is not zero but a small value which is 12.3 mV. Due to this voltage across the transistor, the LED recieves slightly lesser voltage than if it were connected directly. Here is the task done physically

Task 14: LED Brightness Control Using PWM and MOSFET (Power Electronics)

Objectives: Use an Arduino and an N-channel MOSFET to control LED brightness through Pulse Width Modulation (PWM). The Arduino sends a signal to the MOSFET’s gate, allowing current flow between the drain and source. By varying the PWM duty cycle, you can control the LED’s brightness — higher duty cycle means more brightness, and lower duty cycle means dimmer output.

Software used: Arduino IDE

Outcomes and Learnings: The objective of this task is to learn how MOSFET can be used as a switch and how to control the brightness of a LED using Pulse Width Modulation (PWM) of an Arduino. PWM control of brightness: Microcontrollers such as Arduino cannot output analog voltages (such as 2.5V) but can only output discrete voltages (such as 0V or 5V). Hence to simulate analog output, PWM is used in which the digital signal is switched between HIGH and LOW at a very high frequency (490 Hz). N-channel MOSFET as a switch: While an Arduino can generate a PWM signal, its GPIO pins are limited to a maximum continuous current of approximately 20mA to 40mA. High-power LEDs, LED strips, or loads requiring external voltage sources (such as 9V or 12V) cannot be driven directly by the Arduino without damaging the microcontroller. That is why an N-Channel MOSFET is utilized as a voltage-controlled semiconductor switch to bridge this power gap. Here are the pictures and video of my experiment. image1

Task 16: Generating an AC-Like Signal Using a 555 Timer and MOSFETs (Power Electronics)

Objectives: Use a 555 Timer IC to generate a square wave signal and drive two N-channel MOSFETs in a push-pull configuration. As the timer alternates between HIGH and LOW, one MOSFET connects the load to ground while the other pulls it to Vcc, producing an AC-like square waveform. The MOSFETs amplify the signal, enabling the circuit to handle higher current loads.

Outcomes and Learnings: This task demonstrated the conversion of DC signal to an AC like signal using a 555 timer IC in astable mode. Its output alternates between HIGH and LOW at a fixed frequency. This signal is applied to a P-channel and N-channel MOSFET push-pull stage. When the 555 output is HIGH, the N-channel MOSFET conducts and pulls the output toward ground. When the output is LOW, the P-channel MOSFET conducts and pulls the output towards Vcc. Thus the MOSFETS produce an AC like signal while also allowing the circuit to handle a higher current than which the 555 timer can normally withstand. Here is my task demonstration image

UVCE,
K. R Circle,
Bengaluru 01